संस्थान के विवरण


  •  [Ningxia,China]
  • व्यवसाय प्रकार:व्यापार कंपनी , उत्पादक
  • Main Mark: अफ्रीका , अमेरिका की , एशिया , कैरेबियन , पूर्वी यूरोप , यूरोप , मध्य पूर्व , उत्तरी यूरोप , ओशिनिया , अन्य बाजार , पश्चिम यूरोप , दुनिया भर
  • निर्यातक:81% - 90%
  • प्रमाणपत्र:GMP, HACCP, ISO9001, ISO9002, GS
  • विवरण:Activated Carbon Odor,Activated Carbon Refill,Activated Carbon Water Filtration
जांच की टोकरी (0)
ऑनलाइन सेवा

Active Carbon Cylinder bulk environmental

को साझा करें:  
    भुगतान प्रकार: L/C,T/T
    Incoterm: FOB,CFR,CIF
    प्रसव के समय: 90 दिनों

बुनियादी जानकारी

मॉडल नं.: hunhe

कृत्रिम ग्रेफाइट प्रकार: ग्रेफाइट कक्षा की पारगम्यता

सक्रिय कार्बन सामग्री: कोला सक्रिय कार्बन

कार्बन सामग्री: उच्च कार्बन

ताकना व्यास: macroporous

विनिर्माण पद्धति: सक्रिय कार्बन की शारीरिक-रासायनिक पद्धति

प्रकार: तरल-चरण सोशोधन

दिखावट: अनाकार बारीक

प्रयोग: पेट्रोकेमिकल उद्योग, इलेक्ट्रिक पॉवर इंडस्ट्री, खाद्य उद्योग, रासायनिक उद्योग, पर्यावरण संरक्षण उद्योग

Physical Properties: Shape

Chemical Properties: Ph Value

शोषण गुण: मेथिलिन ब्लू शोषण मूल्य

Shape: Amorphous

Colour: Black

Additional Info

पैकेजिंग: bag

उत्पादकता: >10000ton

परिवहन: Ocean,Land

उद्गम-स्थान: Ningxia China

आपूर्ति की क्षमता: >100000ton

प्रमाण पत्र: standard

बंदरगाह: Port of Shanghai,Port of Shenzhen,Port of Tianjin

उत्पाद विवरण

Physical properties of activated carbon testing project introduces 8 items: moisture, ash, particle size, strength, packing density, ignition point, floating rate, pH value.
1, moisture
Moisture is an invalid component of activated carbon, the lower the better.

Drying method is generally used, that is, the carbon sample into a pre-dried and constant weight with a lid weighing bottle, accurately weighed 3 to 5 grams of activated carbon samples, and then placed in an electric oven, at (150 ± 5) ℃ temperature drying at constant temperature above 2h to constant weight, and then placed in a desiccator, cooled to room temperature and weighed. The moisture content is expressed as a percentage of the mass of the lost sample.

active carbon

2, ash
Ash refers to the residue of inorganic salts or oxides remaining after burning at a high temperature, the lower the better.
After a certain mass of activated carbon sample which has been dried in an oven at (150 ± 5) ° C for 2h is burned at (800 ± 25) ° C for 1h, the percentage of the residue obtained from the sample is the ash content of the activated carbon .
3, wear strength strength is the ability of anti-damage activated carbon, the higher the better. GB using the ball mill method, take 50ml dried, a good selection of samples, placed in a drum with five balls, according to a certain speed operation 5min, remove the sample sieved 5min, with the retained in the strength test sieve The percentage by mass of active carbon sample taken by the particles is taken as the strength of the activated carbon.
4, particle size (distribution) Activated carbon particle size of activated carbon bed pressure drop and adsorption speed.

Measurement, according to the technical requirements of the product, select a corresponding set of standard sieve, according to the size of the sieve from the top down and placed on the sieve shaker, weighed 100g of activated carbon sample sieve sieve placed in the upper sieve, Start the vibration sieve machine vibration for 10 minutes, and then in turn remove the layers of sieve, collect and weigh the samples on each sieve layer, calculate the sample retained in the sieve layer on the quality of the sample mass percentage, get activated carbon particle size distributed.

active carbon

5, packing density
Also known as pile weight, affect the size of the device design and floating rate.
The dried activated carbon sample by the vibration feeder at a speed of 0.75 ~ 1.0ml / s free fall into the measuring cylinder, take the volume of filling and weighing the quality of the known activated carbon, the ratio of the packing density.
6, the fire point

Since the adsorption of activated carbon for gas phase adsorption is exothermic, the carbon layer may ignite if sufficient thermal conductivity of the carbon layer is not considered. Therefore, the detection of activated carbon ignition point is necessary. In the air flow at a constant heating rate of heating the sample, with the temperature rise, the carbon-like temperature will suddenly exceed the temperature of the air into the charcoal layer, the temperature at this point is the ignition point of activated carbon.

activated carbon

7, floating rate
Flotation rate is a measure of activated carbon in water or floating in the liquid phase of a performance, the lower the better.

The dried and cooled 20g sample placed in 500ml beaker, add 200ml of distilled water at room temperature and stirred 2 times, allowed to stand for 10min, the sample floating on the water removed after drying and weighed to calculate the floating rate.

activated carbon

8, pH value
pH is an indicator of acid-base activity of activated carbon and needs to be tested for different uses.
First determine the moisture of activated carbon, calculate the equivalent of 10g dry carbon weight of wet carbon quality and weighed into the conical flask. Take boiled distilled water 100mL, add the flask and charcoal shake. On the heating plate on the heating boil the water, keep boiling 15min, remove the flask, the flask was filtered and the filtrate was cooled to 50 ℃, make up to 100mL, with a calibrated pH meter test.

उत्पाद श्रेणियाँ : रसायन उत्पाद > कार्बन उत्पाद

उत्पाद छवियाँ
  • Active Carbon Cylinder bulk environmental
  • Active Carbon Cylinder bulk environmental
  • Active Carbon Cylinder bulk environmental
  • Active Carbon Cylinder bulk environmental
  • Active Carbon Cylinder bulk environmental
इस आपूर्तिकर्ता को ईमेल
  • *विषय:
  • *संदेश:
    आपका संदेश 20-8000 वर्णों के बीच होना चाहिए
आपूर्तिकर्ता के साथ संवाद?आपूर्तिकर्ता
मैं तुम्हारे लिए क्या कर सकते हैं?
आपूर्तिकर्ता से संपर्क करें